MCZ-SERIES TRAK, Relay module, Number of contacts: 1, NO contact AgSnO, Rated control voltage: 48 V…110 V DC +25 % / -30 %, Continuous current: 6 A, Tension-clamp connection, Test button available: No
Technical Specifications:
| Depth | 63.2 mm |
| Depth (inches) | 2.488 inch |
| Height | 91 mm |
| Height (inches) | 3.583 inch |
| Width | 6.1 mm |
| Width (inches) | 0.24 inch |
| Net weight | 27.2 g |
| Storage temperature | -40 °C…85 °C |
| Operating temperature | -25 °C…70 °C |
| Humidity | 95 % for 30 days, minimal condensation to EN 50155 |
| Note room temperature (service) | +85 °C for 10 minutes |
| RoHS Compliance Status | Compliant with exemption |
| RoHS Exemption (if applicable/known) | 7a, 7cI |
| REACH SVHC | Lead 7439-92-1 |
| SCIP | 35d83707-6a3b-45b5-b9f8-6ba8184c863e |
| Rated control voltage | 48 V…110 V DC +25 % / -30 % |
| Rated current DC | <3 mA |
| Power rating | <300 mW |
| Status indicator | Green LED |
| Protective circuit | Free-wheeling diode Varistor Reverse polarity protection |
| Max. reset time after voltage interruption | 10 ms |
| Rated switching voltage | 250 V AC |
| Continuous current | 6 A |
| Max. switching frequency at rated load | 0.1 Hz |
| Max. switching voltage, AC | 250 V |
| Max. switching voltage, DC | 250 V |
| Min. switching power | 100 mA @ 12 V |
| Inrush current | 6 A |
| AC switching capacity (resistive), max. | 1500 VA |
| DC switching capacity (resistive), max. | 120 W @ 24 V |
| Switch-on delay | <4 ms |
| Switch-off delay | <100 ms |
| Contact type | 1 NO contact (AgSnO) |
| Mechanical service life | 10 x 106 switching cycles |
| Version | for railway applications |
| Rail | TS 35 |
| Test button available | No |
| Mechanical switch position indicator | No |
| Open sides | right |
| Colour | beige |
| UL94 flammability rating component | Component: Housing UL94 flammability rating: V-0 |
| Rated voltage | 300 V |
| Pollution severity | 2 |
| Surge voltage category | III |
| Clearance and creepage distances for control side – load side | ≥ 5.5 mm |
| Dielectric strength for control side – load side | 4 kVeff / 1 s |
| Dielectric strength to mounting rail | 4 kVeff / 1 Min. |
| Impulse withstand voltage | 4 kV (1.2/50 µs) |
| Protection degree | IP20 |
| Wire connection method | Tension-clamp connection |
| Stripping length, rated connection | 8 mm |
| Clamping range, rated connection | 1.5 mm² |
| Clamping range, min. | 0.5 mm² |
| Clamping range, max. | 1.5 mm² |
| Wire connection cross section AWG, min. | AWG 26 |
| Wire connection cross section AWG, max. | AWG 16 |
| Wire cross-section, solid, min. | 0.5 mm² |
| Wire cross-section, solid, max. | 1.5 mm² |
| Wire cross-section, solid, min. (AWG) | AWG 26 |
| Wire cross-section, solid, max. (AWG) | AWG 16 |
| Wire connection cross section, finely stranded, min. | 0.5 mm² |
| Wire connection cross section, finely stranded, max. | 1.5 mm² |
| Wire cross-section, finely stranded, min. (AWG) | AWG 26 |
| Wire cross-section, finely stranded, max. (AWG) | AWG 16 |
| Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min. | 0.5 mm² |
| Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max. | 1.5 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), min. | 0.5 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), max. | 1.5 mm² |
| Blade size | 0.6 x 3.5 mm |
Reviews
There are no reviews yet.