Display, Input : Frequency, Output : Display, analogue V / mA
Technical Specifications:
| Depth | 120 mm |
| Depth (inches) | 4.724 inch |
| Height | 48.8 mm |
| Height (inches) | 1.921 inch |
| Width | 96.6 mm |
| Width (inches) | 3.803 inch |
| Net weight | 295 g |
| Storage temperature | -40 °C…80 °C |
| Operating temperature | -20 °C…60 °C |
| RoHS Compliance Status | Compliant with exemption |
| RoHS Exemption (if applicable/known) | 6c, 7a, 7cI |
| REACH SVHC | Lead 7439-92-1 Potassium perfluorobutane sulfonate 29420-49-3 |
| SCIP | f4905d12-f516-4eb5-90a8-8c87685bc956 |
| Cycle time | 2.2 times / s |
| Decimal point | configurable 9.999 99.99 999.9 9999 |
| Dimmable | Yes |
| Display range | -1999…9999 |
| Display value | current measured value Percentage or real value display Switching status |
| Format | 14 segment (numbers + letters) Scrolling text in 8 languages in case of error (e.g. sensor wire breakage, input overrange…) |
| Scaling | Variable |
| Type | red LED 4-character display Digit size: 13.8 mm |
| Accuracy | absolute accuracy: <±0.1 % of the measurement range |
| Configuration | Front push-button |
| DIN Rail compatibility | No |
| Power consumption | ≤ 3.5 W |
| Protection degree | IP20 IP65 (in plugged condition) IP65 |
| Temperature coefficient | ≤0,01% of measurement range⁄°C |
| Type of connection | Tension clamp connection with actuator |
| Type of mounting | Frontpanel mounting Front mounting |
| Voltage supply | 21.6…253 VAC, (50…60 Hz) or 19.2…300 VDC |
| Input frequency | 0.001…50 kHz |
| Min. pulse duration (reset input) | 20 μs…999,9 s |
| Number of inputs | 1 |
| Response time | ≤ 1 Period + 100 ms |
| Sensor | S0 (trig-level low: ≤2.2 mA high: ≥9.0 mA ) Special current (trig-level: user-defined) Special voltage (trig-level: user-defined) TTL (trig-level low: ≤0.8 V high: ≥2.0 V) Tacho (trig-level low: ≤-50 mV high: ≥+50 mV) NAMUR sensor, according to EN60947-5-6 NPN / PNP transistor (trig-level low: ≤4 V high: ≥7 V ) Trigger level adjustable Switch |
| Sensor supply | 5…17 V |
| Type | Adjustable frequencies |
| Alarm function | Over / under frequency Overspeed / underspeed Holding function can be activated |
| Hysteresis | 0…100 % |
| Max. switching voltage, AC | 250 V |
| Max. switching voltage, DC | 30 V |
| Number of digital outputs | 2 |
| Rated switching current | 2 A |
| Rated switching voltage | 24 V AC … 250 V AC |
| Switch-off delay | 0…3600 s |
| Switch-on delay | 0…3600 s |
| Switching capacity | 500 VA |
| Switching thresholds | Adjustable |
| Switching thresholds | All values in display range are configurable |
| Type | 2 x 1 CO contact (hard gold-plated) |
| Type of switch function | direct or inverted |
| Load resistance current | ≤ 800 Ω |
| Number of analogue outputs | 1 |
| Output behaviour on failure downscale | 3.5 mA |
| Output behaviour on failure upscale | 23 mA |
| Signal output | direct or inverted |
| Type (analogue output) | ‘active’,’connected control must be passive’ |
| EMC standards | EN 61326-1 |
| Galvanic isolation | between input ⁄ output ⁄ supply ⁄ relay |
| Insulation voltage | 2.3 kVAC (Test) / 250 VAC (operating state) |
| Pollution severity | 2 |
| Surge voltage category | II |
| Wire connection method | Clamping yoke pluggable |
| Type of connection | Tension clamp connection with actuator |
| Wire connection cross section AWG, min. | AWG 30 |
| Wire connection cross section AWG, max. | AWG 16 |
| Wire connection cross section, finely stranded, min. | 0.13 mm² |
| Wire connection cross section, finely stranded, max. | 2.8 mm² |
Reviews
There are no reviews yet.