Frequency signal converter, including rail bus supply, Input : Frequency, Output : 0(4)-20 mA, 0(2)-10 V
Technical Specifications:
| Depth | 114.3 mm |
| Depth (inches) | 4.5 inch |
| Height | 112.5 mm |
| Height (inches) | 4.429 inch |
| Width | 6.1 mm |
| Width (inches) | 0.24 inch |
| Net weight | 80 g |
| Storage temperature | -40 °C…85 °C |
| Operating temperature | -25 °C…70 °C |
| Humidity | 0…95 % (no condensation) |
| RoHS Compliance Status | Compliant with exemption |
| RoHS Exemption (if applicable/known) | 7a, 7cI |
| REACH SVHC | Lead 7439-92-1 |
| SCIP | 2f6dd957-421a-46db-a0c2-cf1609156924 |
| Input frequency | adjustable 0…100kHz |
| Number of inputs | 1 |
| Sensor | NAMUR sensor, according to EN60947-5-6 NPN / PNP transistor (trig-level low: ≤4 V high: ≥7 V ) TTL (trig-level low: ≤0.8 V high: ≥2.0 V) Tacho (trig-level low: ≤-50 mV high: ≥+50 mV) Special current (trig-level: user-defined) Special voltage (trig-level: user-defined) S0 (trig-level low: ≤2.2 mA high: ≥9.0 mA ) |
| Sensor supply | 5…17 V |
| Load impedance current | ≤ 600 Ω |
| load impedance voltage | ≥ 10 kΩ |
| Number of outputs | 1 |
| Output current | 0…20 mA 4…20 mA in case of sensor error downscale (3,5 mA) upscale (23 mA) |
| Output signal limit | <28 mA |
| Output voltage, note | 0(2)…10 V 0(1)…5 V 0(0,2)…1 V |
| Type | active connected control must be passive |
| Accuracy | Basic accuracy: 0.0002 Hz |
| Configuration | DIP switch or via FDT/DTM software |
| Nominal power consumption | 0.5 VA |
| Operating altitude | ≤ 2000 m |
| Power consumption, max. | 1.2 W |
| Power consumption, typ. | 0.65 W |
| Protection degree | IP20 |
| Rail | TS 35 |
| Step response time | ≤ 30 ms (0…90% / 100…10% of input level) |
| Temperature coefficient | ≤0,01% of measurement range⁄°C |
| Voltage supply | 24 V DC ±30 % at terminal or via CH20M rail bus |
| EMC standards | IEC 61326-1 |
| Galvanic isolation | 3-way isolator |
| Insulation voltage | 2.5 kVeff /1 min. |
| Pollution severity | 2 |
| Rated voltage | 250 V 300 V |
| Surge voltage category | II |
| Type of connection | Screw connection |
| Tightening torque, min. | 0.4 Nm |
| Tightening torque, max. | 0.6 Nm |
| Clamping range, rated connection | 2.5 mm² |
| Clamping range, min. | 0.5 mm² |
| Clamping range, max. | 2.5 mm² |
| Wire connection cross section AWG, min. | AWG 30 |
| Wire connection cross section AWG, max. | AWG 14 |
| EMC standards | IEC 61326-1 |
| Standards | IEC 61010-1 |
Reviews
There are no reviews yet.