TERMSERIES, Relay module, Number of contacts: 2, CO contact AgNi, Rated control voltage: 230 V UC ±5 %, Continuous current: 8 A, PUSH IN, Test button available: Yes
Technical Specifications:
| Depth | 97.5 mm |
| Depth (inches) | 3.839 inch |
| Height | 89.4 mm |
| Height (inches) | 3.52 inch |
| Width | 12.8 mm |
| Width (inches) | 0.504 inch |
| Net weight | 61 g |
| Storage temperature | -40 °C…70 °C |
| Operating temperature | -40 °C…60 °C |
| Humidity | 5-85% relative humidity, Tu = 40°C, without condensation |
| RoHS Compliance Status | Compliant with exemption |
| RoHS Exemption (if applicable/known) | 7a, 7cI |
| REACH SVHC | Lead 7439-92-1 |
| SCIP | 9e2cbc49-76d9-4611-b8ec-5b4f549a0aa9 |
| Connection cross-section AWG, min. | AWG 26 |
| Connection cross-section AWG, max. | AWG 14 |
| Type of conductor | rigid copper conductor flexible copper conductor |
| Pollution severity level | 2 |
| Rated control voltage | 230 V UC ±5 % |
| Rated current DC | 4.3 mA |
| Status indicator | Green LED |
| Protective circuit | Free-wheeling diode Reverse polarity protection |
| Coil voltage of the replacement relay deviating from the rated control voltage | Yes |
| Coil voltage of the replacement relay | 110 V DC |
| Rated switching voltage | 250 V AC |
| Continuous current | 8 A |
| Max. switching frequency at rated load | 0.1 Hz |
| Max. switching voltage, AC | 250 V |
| Max. switching voltage, DC | 250 V |
| Min. switching power | 100 mA @ 10 V |
| Inrush current | 30 A / 4 s |
| AC switching capacity (resistive), max. | 2000 VA |
| DC switching capacity (resistive), max. | 46W @ 230V |
| Switch-on delay | ≤ 15 ms |
| Switch-off delay | ≤ 16 ms |
| Protective circuit, load side | Rectifier |
| Contact type | 2 CO contact (AgNi) |
| Mechanical service life | 5 x 106 switching cycles |
| Operating altitude | ≤ 2000 m above sea level |
| Rail | TS 35 |
| Test button available | Yes |
| Version of test button | Momentary test button Lockable test button |
| Mechanical switch position indicator | Yes |
| Colour | black |
| UL94 flammability rating component | Component: Housing UL94 flammability rating: V-0 Component: Pusher UL94 flammability rating: V-0 Component: Retaining clip UL94 flammability rating: V-0 |
| Rated voltage | 300 V |
| Pollution severity | 2 |
| Surge voltage category | III |
| Clearance and creepage distances for control side – load side | ≥ 5.5 mm |
| Dielectric strength for control side – load side | 2.5 kVeff / 1 Min. |
| Type of isolation at input and output | reinforced insulation |
| Dielectric strength of open contact | 1 kVeff / 1 min |
| Dielectric strength to mounting rail | 4 kVeff / 1 Min. |
| Impulse withstand voltage | 6 kV (1.2/50 µs) |
| Impulse withstand voltage at neighbouring contacts | 4 kV (1.2/50 µs) |
| Protection degree | IP20 |
| Certificate no. (cULus) | E141197 |
| Wire connection method | PUSH IN |
| Stripping length, rated connection | 9 mm |
| Clamping range, rated connection | 1.5 mm² |
| Clamping range, min. | 0.14 mm² |
| Clamping range, max. | 2.5 mm² |
| Wire connection cross section AWG, min. | AWG 26 |
| Wire connection cross section AWG, max. | AWG 14 |
| Wire cross-section, solid, min. | 0.14 mm² |
| Wire cross-section, solid, max. | 1.5 mm² |
| Wire cross-section, solid, min. (AWG) | AWG 26 |
| Wire cross-section, solid, max. (AWG) | AWG 16 |
| Wire connection cross section, finely stranded, min. | 0.14 mm² |
| Wire connection cross section, finely stranded, max. | 2.5 mm² |
| Wire cross-section, finely stranded, min. (AWG) | AWG 26 |
| Wire cross-section, finely stranded, max. (AWG) | AWG 14 |
| Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min. | 0.25 mm² |
| Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max. | 1.5 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), min. | 0.25 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), max. | 1.5 mm² |
| Wire connection cross section, finely stranded, two clampable wires, min. | 0.5 mm² |
| Wire cross-section, finely stranded, two clampable wires, max. | 1 mm² |
| Blade size | 0.4 x 2.0 mm |
Reviews
There are no reviews yet.